Product Information
| Model Number | YF11-#9074 | Brand Name | OEM |
|---|
| origin | China | Small Orders | Accepted |
|---|
Key Specifications/ Special Features:
1、 Safety tips
♦ Recommend the accessories / accessories specified by the manufacturer.
♦ This product uses alkaline 5 / 7 batteries.
♦ Do not forcibly remove the product to avoid damage to the product.
♦ Do not scrape the fingerprint collector with sharp objects, otherwise it may cause permanent damage.
♦ Do not expose the product to water leakage or splashing environment.
♦ Do not contact the product to corrosive substances to avoid the protective layer.
♦ Clean the products, please wipe them with a soft cloth.
♦ Do not remove the battery during the setup operation.
♦ After the door lock triggers the low power alarm, please replace all the batteries in time and ensure that the positive and negative electrodes of the battery are installed correctly.
2、 Warning instructions
♦ Do not bring the battery close to the fire source to avoid an explosion.
♦ Do not use metal to connect the poles of the battery lead, so as to avoid explosion.
3、
Product schematic diagram
3.1 Product physical picture
4、 Product Settings
4.1 Menu navigation diagram
4.2 Key function
[0-9] keys are the digital keys ;
The [*] key can be used as a clear key , or a back key ;
The [#] key can be used as a doorbell key, or a confirmation key.
4.3 User management
4.3.1 User type
① Administrator: you can unlock, add / delete users, and enter the menu to modify the
system parameters
② Ordinary users: they can only unlock it normally
4.3.2 Type of entry
The maximum storage capacity is 200, and can support the input of fingerprint, password,
card and other information
type quantity Other instructions
loops and whorls on a finger Support for 50 fingerprint ID
(Up to 10 administrator users and 50
ordinary users) The default number of entries is 5 times
M1 card Up to 200 ID is supported Support for the encryption of the M1 card
password Up to 200 ID is supported Support for a 6-12-bit password input
4.3.3 Edit the user
Enter the entered ID number, such as 002, and you can operate on it,
① Disable user: disable the ID to unlock (if an administrator, it will not affect the menu)
② Re-input: re-input the password / card / fingerprint to cover the original user
information
4.3.4 Delete the user
① Delete by the number: enter the entered ID number, and delete a single user information
after confirmation
② Delete by type: Select different types to delete, and delete the user information of the
same type after confirmation
③ Delete all: delete all user information
Note: Administrator 001 cannot be deleted by default and can only be reset by initializing
the system
4.3.5 Disable unlocking
After selection, prohibit the same type of user (password / card / fingerprint) in the
motherboard to unlock
(If an administrator, it will not affect its entry into the menu)
4.4 System Settings
4.4.1 Time setting
According to the voice / screen display prompt, you can set the time of the lock board,
Input format: 20 XX year XX month XX day xx hour xx minute.
4.4.2 Language volume
① Language: you can choose Chinese and English voice broadcast and screen display text,
the default is Chinese.
② Volume: you can choose low volume, high volume, the default high volume option.
4.4.3 Lock setting
① Single unlock: verify one only user when unlock (default option).
② Combination of unlocking: Two users need to be verified when unlocking.
③ Lock time: lock-lock interval, can set 2-9s, the default is 5s.
④ Often open mode: after opening, the motherboard will automatically unlock, and
continue to keep the unlocking state;
4.4.4 Other settings
① Anti-skid alarm: anti-skid alarm is 180s, the default is closed.
② Restore the factory settings: after confirmation, the system data can be reset.
4.5 System query
4.5.1 record management
Record the operation log in the system (including unlocking, input and alarm).
4.5.2 store information
Record the storage space in the system, the total number of users is 200, more than 500
logs.
4.5.3 Version information
Record the current lock number, and the software version number.
4.5.4 Lock ID
Displays the number of the current lock plate, which can be used to generate temporary
password credentials
4.6 Remote management
4.6.1 Add remote users
According to different manufacturers' modules, you can choose WiFi fast connection and
hot spot sharing on the front board for network connection.
4.6.2 Remove remote users
You can send commands at the lock board end to reset the rear board networking module.
5、 Other instructions
★ password anti-test:
When the wrong unlocking information is entered more than 3 times , the system will give an alarm.5 times, the system will lock for 90 seconds
★ Password anti-snoop:
Can you add other numbers before and after entering the correct password, such as: XXX password XXX, the password must be continuously entered), the panel can input 12 + 20 bits (12-bit valid password, 20-bit virtual password)
★ Automatic dormancy:
After setting the setting page for 20 seconds and the verification page for 10 seconds, the
system hibernation will automatically quit.
★ Low voltage alarm:
After the voltage is lower than 4.8V, there will be a voice prompt "low battery power" when wake. Please replace the new battery as soon as possible.
★ Normally-open mode:
① After using the administrator user to unlock, press [5] and then press [#] key to open
② Modify in the system settings
★ Aging mode:
In the initialization state, press [999] + [#] to enter the aging mode, the system will continue to switch the lock, and press [*] to exit the mode.
★ Set the lock number:
In the main interface, press [999876] + [#] to verify the administrator, after successful operation, you can enter the number, press [#] to confirm, you can view in the system menu.
★ Switching motor direction:
In the initialized state of the system,press [888#], the system will prompt “1. left turn, 2. right turn”, the system default setting for the left door, press the numeric key to modify; When the registered user, the function item will prohibit settings
6、 Technical parameter
power suppl Rated voltage DC 4.8V-6.5V (four sizes 5 / 7, dry battery)
working current The average working current is within 200 mA, and the maximum current is about 300 mA
quiescent current ≤50μA
Fingerprint parameters Resolution 508 DPI, support for 50 fingerprint ID
Fingerprint
rejection
Rate FRR. <1%
Fingerprint false rate
FAR. <0.001%
NFC card
parameters Support Mi fare card, frequency 13.56MHZ;
The unlocking distance of 3mm acrylic is 1cm;
Support encryption, up to 200 cards can be input
Password parameters Support 6-12 bit passwords, up to 200 passwords
working temperature -25℃~60℃
Anti-static ability Contact discharge is ± 8 KV
Air discharge is ± 15 KV
emergency service Support for 5V mobile power supply USB port
other Support main line burning
7、IoT mobile app operation instructions
/7.1 Download method
Method 1: you can search for "Tuya Smart / Smart life" in app Store or Android app stores, download and install it;
Method 2: scan the QR code below to download application.
graph 16. Tuya Smart (left) graph 17.Smart life (right)
7.2 Connection operation instructions
7.2.1 Confirm the WiFi frequency band
Confirm that the connected WiFi band is 2.4GHz band. You can view the connected WiFi band in the mobile phone WiFi setting according to the figure shown below;
Details Images
Product Certifications
| Certificate Standard |
CE
|
|---|
| Certificate Image | Click on the picture to see a larger one |
|---|
| Certificate Number | LH-221203155990 |
|---|
| Validity | From 2023/03/07 |
|---|
| Issued By | SHENZHEN LH Testing Technology co.,ltd |
|---|
Note: Not all certifying agents offer online lookup, and some have a lag time for posting new certificates. If you are unable to find a certificate online, contact the certification agency or supplier for further verification.
Shipping Information
| FOB Port | Shenzhen | Lead Time | 15–20 days |
|---|
| Weight per Unit | 3.0 Kilograms | Dimensions per Unit | 45.0 x 30.0 x 15.0 Centimeters |
|---|
| Units per Export Carton | 10.0 | Export Carton Dimensions L/W/H | 50.0 x 18.0 x 12.0 Centimeters |
|---|
| Logistics attributes | Common | Export Carton Weight | 2.0 Kilograms |
|---|
Main Export Markets
| Main Export Markets |
Asia,
Australasia,
Central/South America,
Eastern Europe,
Mid East/Africa,
North America,
Western Europe |
|---|
Payment Details
| Payment Method | Telegraphic Transfer in Advance (Advance TT, T/T) |
|---|